Fluke

  • Filter
Created on: 12 February 2014

Current Range: 1 to 600 A DC or AC Peak Basic Accuracy (DC to 400 Hz): +/- (2% of reading + 1 A) Output Signal: 100 A range: 10 mV/A | 600 A range: 1 mV/A Frequency Range: 40 Hz to 400 Hz Working Voltage: 600 V AC rms Maximum Conductor Diameter: 34 mm (1.34 inch) Safety Rating: IEC 1010 and CSA-C22.2 No. 1010-1 Installation Category II, Working Voltage 600V

Created on: 16 February 2014

Qualifies - Sees if your existing cabling has the bandwidth to support voice, 10/100, VoIP or Gigabit Ethernet Troubleshoots - shows why existing cabling cannot support the network's bandwidth requirement (e.g. crosstalk at 11 meters) Discovers - detects what's at the end of any cable and displays device configuration (speed/duplex/pairing) Identifies unused switch ports that can be reallocated Graphically maps wiring configuration and shows distance to faults with Intelligent Wiremap Tests all copper cabling media: twisted-pair, coax, and audio cabling

Created on: 16 February 2014

NetProve diagnostics – isolate device and application connectivity issues in seconds Inline Gigabit vision - quickly troubleshoot network problems with powerful inline vision into 10/100/Gig traffic between switches, PCs, IP phones and other devices NetSecure monitoring and authentication - identify spyware, malware, and viruses with port monitoring; troubleshoot authentication issues with 802.1x log VoIP troubleshooting - connect inline for visibility into VoIP calls to quickly diagnose IP phone boot-up and call control problems and to measure key call quality metrics PoE Measurements - verify readiness of PoE systems and troubleshoot PoE device problems Spot available network resources – See MAC and IP addresses, subnet and services offered by active servers, routers and printers IntelliTone digital signaling - quickly and safely locate cables on active network

Created on: 16 February 2014

Superior high-impedance monitoring Data indication/warning Low & high voltage indication/warning Low current (mA) indication/warning Passive monitor 2-Way hands-free speakerphone Low battery warning Mute indication Polarity indication Tone & pulse dialing (Optional) 1-Way amplified speakerphone mode Amplified speaker Last number redial Over voltage protection Over current protection Mute PBX pause button Audible ringer Speed dialing Volume control levels Line and battery powered Hearing aid compatible Waterproof case design for sever weather conditions, exceeds American Military Spec MIL-STD-810E DropSafe™ 20ft onto concrete Mountable, top or bottom, extra large steel locking belt clip Line cord strain relief TS44 includes Patented DSL/POTS filtering technologies TS44 includes Data Lockout TS44 includes Lockout Override

Created on: 12 February 2014

Nominal Voltage: 4.8V Capacity: 1800 mAh

Created on: 14 February 2014

600 A ac current measurement with fixed jaw 600 V ac and dc voltage measurement True-rms ac voltage and current for accurate measurements on non-linear signals Resistance measurement to 6000Ω with continuity detection 1000 µF capacitance measurement State of the art signal processing allows for use in noisy electrical environments while providing stable readings Large, easy to read, backlight display automatically sets the correct measurement range so you do not need to change switch positions while taking a measurement CAT IV 300 V, CAT III 600 V safety rating

Created on: 16 February 2014

Versiv's modular design supports copper certification, fiber loss, OTDR testing and fiber end-face inspection Taptive user interface provides simple, animated guidance to eliminate incorrect reference setup and “negative loss” errors. Fastest time to certify – two fibers at two wavelengths in three seconds. Encircled Flux compliant as required by ANSI/TIA and ISO/IEC with no additional test cords Merged Tier 1 (Basic) / Tier 2 (Extended) testing and reporting when paired with OptiFiber Pro ProjX management system ensures all jobs are completed correctly and efficiently Built in Visual Fault Locator Analyze test results and create professional test reports using LinkWare Management Software

Category: Taps
Created on: 16 February 2014

Plug-and-play simplicity for fast analysis and deployment Decrease budget required for visibility on redundant links Single interface monitoring and analysis for full duplex links Dual link models are ideal for meshed trunk analysis using single port analysis devices Media conversion for Gigabit links expands the reach of your existing analysis solutions Eliminates the need for spanning resources and configurations